<bdo id="fou7v"></bdo><delect id="fou7v"></delect><noframes id="fou7v"><delect id="fou7v"></delect><delect id="fou7v"><bdo id="fou7v"></bdo></delect><delect id="fou7v"><rt id="fou7v"></rt></delect><delect id="fou7v"></delect><bdo id="fou7v"></bdo><noframes id="fou7v"><bdo id="fou7v"><rt id="fou7v"></rt></bdo><noframes id="fou7v"><rt id="fou7v"><rt id="fou7v"></rt></rt> <noframes id="fou7v"><delect id="fou7v"><delect id="fou7v"></delect></delect><delect id="fou7v"></delect><noframes id="fou7v"><rt id="fou7v"><rt id="fou7v"></rt></rt><noframes id="fou7v"><bdo id="fou7v"><rt id="fou7v"></rt></bdo><noframes id="fou7v"><noframes id="fou7v"><noframes id="fou7v"><rt id="fou7v"></rt><rt id="fou7v"></rt> <noframes id="fou7v"><delect id="fou7v"><delect id="fou7v"></delect></delect><rt id="fou7v"><rt id="fou7v"></rt></rt><noframes id="fou7v"><noframes id="fou7v">

佛山超渠榮科技有限公司網歡迎您!

全國服務熱線:

139-2321-4786

新聞資訊,佛山市超渠榮科技有限公司
您當前的位置 : 首 頁 > 新聞中心 > 技術問答

裁斷機故障原因及解決方法

2021-07-07 04:56:00

裁斷機廠家告訴你裁斷機故障原因及解決方法


1、油溫過高

A、油泵的損壞,它的內部零件在高速轉動的時候磨損產生了熱量。

B、油壓組件內漏,比如方向閥扣壞或者是密封圈的損壞,可以使高壓油流經細小空間產生熱量。

C、壓力調節的不當,在液壓系統長期的處于高壓的狀態下而過熱?! ?br/>

2、壓板不下行,或者是下行后不復位。

A、裁斷的開關是有問題的,檢查或者是更換。

B、油箱內的油量不足或者是油管的泄露,加油或者是擰緊油管的接頭。

C、電磁閥不能復位,修復或者是更換。

D、繼電器的接觸不良,主油路是不能切換的,要檢查線路。


3、裁斷壓力不足

A、油泵的損壞或者是進油的路堵塞,油缸有泄露,檢查后要根據情況而定進行排除。

B、微動的開關觸控太慢或者是故障,要調整使其在裁斷點前約10MM的時候碰觸或者是換新。

C、電磁閥的故障,要查修電磁閥的心軸。

D、油箱之循環油的不足,要補充循環油要使油面超過濾油網。


標簽

近期瀏覽:

image.png

微信 掃一掃

聯系方式

聯系電話:139-2321-4786

郵箱:2455400791@qq.com

網址:www.stainlesssteelnebraska.com

地址:廣東省佛山市南海區松崗鎮聯表工業區

在線留言

姓名:
手機:
郵箱:
驗證碼
Copyright ? 佛山市超渠榮科技有限公司 All rights reserved 備案號:粵ICP備2021086456號 主要從事于裁斷機,油壓裁斷機,珍珠棉裁斷機, 歡迎來電咨詢!
色欲AV天堂
<bdo id="fou7v"></bdo><delect id="fou7v"></delect><noframes id="fou7v"><delect id="fou7v"></delect><delect id="fou7v"><bdo id="fou7v"></bdo></delect><delect id="fou7v"><rt id="fou7v"></rt></delect><delect id="fou7v"></delect><bdo id="fou7v"></bdo><noframes id="fou7v"><bdo id="fou7v"><rt id="fou7v"></rt></bdo><noframes id="fou7v"><rt id="fou7v"><rt id="fou7v"></rt></rt> <noframes id="fou7v"><delect id="fou7v"><delect id="fou7v"></delect></delect><delect id="fou7v"></delect><noframes id="fou7v"><rt id="fou7v"><rt id="fou7v"></rt></rt><noframes id="fou7v"><bdo id="fou7v"><rt id="fou7v"></rt></bdo><noframes id="fou7v"><noframes id="fou7v"><noframes id="fou7v"><rt id="fou7v"></rt><rt id="fou7v"></rt> <noframes id="fou7v"><delect id="fou7v"><delect id="fou7v"></delect></delect><rt id="fou7v"><rt id="fou7v"></rt></rt><noframes id="fou7v"><noframes id="fou7v">